If you’re looking for a quick way to replace the heating element on your Samsung dryer, you’ve come to the right place. In this article, you’ll learn how to take the back cover off of your dryer and how to install a new heating element.
Removing the control panel
If you’re looking to replace the heating element in your Samsung dryer, you may have noticed that you’re getting a tripping breaker. This is a symptom of a defective thermal fuse or thermistor. There are several steps you can take to get to this part of your appliance and fix it, but first you’ll have to remove the control panel.
Before you start, check the user manual for specific instructions on removing the top cover. If you’re having problems, call a repairman to help you.
Next, you’ll need to unplug the dryer from its power socket. You should also check your electrical connections and the venting. Once you’ve done that, you can move the dryer away from the back wall.
To remove the heating assembly, you’ll need to disconnect the wire harnesses. Then, you’ll need to lift the bottom half of the assembly and pull it out of the dryer.
You’ll also need to disconnect the wires from the thermal fuse. Make sure to mark the wires before you begin.
After you’ve done that, you can test the heating element with a multimeter to ensure continuity. You can then replace it if you find it’s not functioning.
Finally, you’ll need to replace the control board. It’s a fairly simple process, but it’s worth the effort.
First, you’ll need to remove the top trim piece. This is a small piece that runs along the front of the dryer. Remove it by unscrewing two screws. Be careful when putting it back in place.
In addition to reinstalling the top trim piece, you’ll need to replace the front plate. Pull out the screw and put it in the envelope.
Removing the back cover
If your Samsung dryer is not heating up, or making loud noises, the first thing to do is to remove the back cover. This will give you access to the main control board. It will also allow you to test the heating element.
The heating element in a Samsung dryer is located in the bottom right corner of the machine. It is a metal box that contains a set of coils. To get to the element, you will need to remove two screws from the back of the unit.
Before removing the back cover, you should unplug the appliance. You should also disconnect the hose and power cord, and then pull the dryer from the wall.
Using the multimeter, you should check the resistance of the heating element to see if it is functioning properly. If it is not, you will need to replace the element.
Before removing the back cover, it is important to make sure you have the correct replacement part. The element can be purchased as an assembly or separately. Depending on your model, you may need to replace the thermostat, too.
Once you have removed the back cover, you can now test the new heating element. Make sure that you are connecting the wires correctly so as not to damage the new element.
Lastly, be sure to store the back cover safely after you’ve finished the repair. Keeping your appliance in good condition is important for the longevity of your machine.
While you are at it, you might as well clean the vents to avoid overheating. In addition, you should clean the heat exchanger.
Changing the heating element in a Samsung dryer is an easy process. A new element will last approximately 15 years.
Removing the thermistor
If you have a Samsung dryer that is making a lot of noise or is taking longer than it should to dry your clothes, the cause might be a burnt out thermistor. The thermistor is one of the main temperature sensors that control the heating function of your dryer. Fortunately, it’s fairly easy to replace.
First, you’ll need to unplug the unit. Doing this protects you from electric shock. Also, you should disconnect power before removing any access panels.
Secondly, you’ll need a screwdriver and a Phillips head bit. Remove the screws holding the thermistor to the blower housing. You can then discard the old thermistor.
Finally, it’s time to install your new thermistor. You’ll want to make sure that you get the manufacturer-approved part.
A multimeter is a good tool to use for this step. It can help you test the various leads on your thermistor to see if they’re functioning correctly.
Another handy gizmo to have on hand is a volt/ohm meter. While you’re at it, you may also want to check out the thermal fuse, which is designed to prevent dryer fires.
Now, you can mount your new thermistor on the blower housing. Just be sure to place it in the same order as the old thermistor.
In addition to the thermistor, you should also replace the heating element. Burnt out elements give off a burnt smell.
Before you begin, read your user manual to understand the access requirements. Be sure to wear work gloves and masking tape. Otherwise, you might hurt yourself.
Having all the tools in place before you start can make your repair go smoother. Plus, you might end up saving money in the long run.
Installing a new heating element
If your Samsung dryer is not heating up properly, it is most likely because the element is burnt out. The element can be easily replaced. You just need to follow a few simple steps.
First, you will need to turn off the power supply. This prevents electrocution.
Next, you will need to remove the top cover and drum of the dryer. After this, you will need to disconnect the wires from the thermostat and thermal fuse. Often, this is located behind the panel on the back of the appliance.
Once all of these parts are removed, you can see the heating element. It is a large metal frame that holds the heating coils. There are six heater terminals. Each terminal has a different shape.
A multimeter is required to test the continuity of the leads. Generally, the resistance of a good heating element is between 9 and 10 ohms.
To install a new heating element, you will need to remove the existing one. The old screw may be used to secure the new one. Also, you will need to replace the thermal fuse.
A service technician is recommended to perform this task. However, it is possible for you to do it yourself. Just be sure that you are aware of the dangers of doing repairs on your appliances.
To replace the heating element in your Samsung dryer, you will first need to disconnect the heating wires from the thermostat. To do this, you will need to open the back of the dryer.
Now that you have removed the elements, you can start replacing the new one. This process will take some time because you will need to manually reach the element housing.
Reconnecting the dryer vent
Fortunately, it is possible to replace the heating element in a Samsung dryer with a few tools and a bit of know-how. This is usually not a difficult task and can be completed in under an hour.
First, you will need to remove the back cover of your dryer. Once the cover is off, you will be able to see the heating element. You may need to use a quarter-inch nut driver to unscrew it. After removing it, you will need to reconnect the hose to the vent. If you have a gas dryer, you will need to turn on the shut-off valve.
You may also need to replace the lint filter. The filter has six power terminals. It should be replaced to avoid overheating.
Alternatively, you could opt to purchase a new timer motor. This is less expensive than the heating element. However, you will need to disconnect your power source before you can test the timer.
Next, you will need to connect the new heating element. Depending on your particular model, the price of the heating element can vary. Typically, it costs around $30 to $100.
Lastly, you should check the thermal fuse. The thermal fuse is a safety device which prevents your dryer from overheating. If the temperature gets too high, the thermal fuse will trip. In order to check, you will need a multimeter to measure the continuity of the thermal fuse.
If you haven’t done this before, you should make sure that you wear a mask. Wearing a mask will protect you from breathing in airborne debris.
When you are done replacing the heating element, you will need to reconnect the vent. Before you do so, you should ensure that the hose doesn’t slip again.